#Arc xt pro recording how to#
#Arc xt pro recording serial#
#Arc xt pro recording software#
#Arc xt pro recording Pc#

To 'read' data from the scanner, you need to either be in Mass Storage Mode, or take the card out of the scanner and use a card reader to read the data into your PC.

#Arc xt pro recording serial#

Serial mode can be used for logging and virtual control. Pri with no on the face of the scanner just below. With the scanner connected to the PC, you should see a prompt on the screen asking whether you want to use Mass Storage Mode-Press E for Mass Storage, or Serial Mode-Press the decimal point key, which is labeled.

#Arc xt pro recording Pc#

To read the 536 either into Sentinel, or to ARC 536 (if you have that), connect the cable that came with the scanner to your PC then plug it into the 536 using the Mini-USB port under the E key. ARC XT Pro (for the 996) cannot read your 536. Sentinel will let you enter an LCN of 0, and when you run the LCN Finder, the scanner will change all the LCNs to zero before starting.Ĭlick to expand.Do you have ARC 536 Pro, to read the scanner? Or only the ARC XT Pro version for just the 996P2. Be sure and save the results when exiting the LCN Finder. If nothing has been found yet, you'll just see a zero as the LCN.

Then, just press Enter without making a change, and you'll next see the LCN> If the scanner found an LCN, you'll see the LCN found. Pess Enter as if you want to edit (or enter a new) frequency.

In the site edit, pull up each frequency. Then, 'edit' the system, and select 'edit' the site. In 'editing', pull up the system in the scanner, select edit the Favorites list. After one or more LCNs are found, then either read the scanner back into ARCXT or Sentinel, to see the values it found, or you can view the results on the scanner by editing the system. Depending on system activity, you may need to let it run anywhere from a few hours to a day or more.

#Arc xt pro recording how to#

The only good side to this scanner is the sensitivity, it is superb.but only after you can get it programed!!!! Now that I have vented, somewhat, can ANYBODY please, in a easy step by step process, help me understand why this could keep happening, and how to fix it.What I did with my local NXDN systems (before this spreadsheet was posted) was to enter all the frequencies for each site, then run the LCN finder on my 436HP or 536HP. This new 996P2, is no comparison to previous models, I never wanted to toss those in the dump. UpMan, or someone at Uniden, please pay attention, I have a BC780XLT, a 996T, and love them both. I haven't even started on the P2 's terrible, but my county radio works great. I am no computer expert, but I can program every one of my other scanners, even Motorola, Ericsson or Harris, and Kenwood two-way radios, but nothing compares to this piece of crap. I bought it from the bearcat warehouse, it came completely unprogrammed, not even weather frequencies, although I was told it would have some basic programming. This scanner has been nothing but a headache and complete PITA in so many ways. I am using both Windows XP and Windows 8. I cannot get the scanner firmware updated because neither of my computers will recognize the scanner driver. I have downloaded the BC VUP3 and unzipped it, no luck. Well today, I decide I want to add to my NC VIPER file, the ARC-Pro reads the scanner, I go thru the motions, try to upload the new talkgroup info, then the computer DOESN'T recognize the scanner. Then, just before I throw the POS2 into my back yard, it reads it. I was on the talkgroup development committee so I had everything I needed for data, (frequencies, talkgroups, etc.) I updated my ARC-Pro, and guess what, it wouldn't recognize the scanner. I bought this 996P2 about two months ago, as my county (Pittsylvania, Va) uses a Harris P2 system.

#Arc xt pro recording software#

Another P2 that software doesn't recognize